ResMed AirCurve 10 ASV w/ HumidAir
Call For Pricing!
- AirCurve 10 ASV Owner's Manual
|Operating Sound Level||27 dBA|
|Pressure Range||4 - 25 cmH2O|
|Water Chamber Capacity||380 mL|
|Warranty||2 Year Limited|
The AirCurve 10 ASV offers truly personalized therapy for central breathing disorders, and associated obstructive events. By treating central breathing disorders with auto-adjusting pressure support, and upper airway obstruction with auto-adjusting EPAP, the ResMed AirCurve 10 ASV works to rapidly stabilize respiration and help improve blood gases.
- Easy-Breathe Comfort Feature
- Built-In HumidAir Heated Humidifier
- TiControl and Adjustable Rise Time
- LCD Displays with My Options
- Enhanced Vsync Technology
- SmartStart / SmartShop
- SD Card and Data Storage
|90W power supply unit|
|AC input range:||100–240V, 50–60Hz 1.0–1.5A, Class II 115V, 400Hz 1.5A, Class II (nominal for aircraft use)|
|DC output:||24V --- 3.75A|
|Typical power consumption:||53W (57VA)|
|Peak power consumption:||104W (108VA)|
|Operating temperature:||+41°F to +95°F (+5°C to +35°C) Note: The air flow for breathing produced by this therapy device can be higher than the temperature of the room. Under extreme ambient temperature conditions (104°F/40°C) the device remains safe.|
|Operating humidity:||10 to 95% relative humidity, non-condensing|
|Operating altitude:||Sea level to 8,500' (2,591 m); air pressure range 1013 hPa to 738 hPa|
|Storage and transport temperature:||-4°F to +140°F (-20°C to +60°C)|
|Storage and transport humidity:||5 to 95% relative humidity, non-condensing|
The AirCurve 10 complies with all applicable electromagnetic compatibility requirements (EMC) according to IEC60601-1-2:2007, for residential, commercial and light industry environments. It is recommended that mobile communication devices are kept at least 1 m away from the device.
Information regarding the electromagnetic emissions and immunity of this ResMed device can be found on www.resmed.com, on the Products page under Service and Support.
IEC 60601-1:2005 classification
Class II (double insulation), Type BF, Ingress protection IP22.
|Pressure sensor:||Internally located at device outlet, analog gauge pressure type, -5 to +45 cm H2O|
|Flow sensor:||Internally located at device inlet, digital mass flow type, -70 to +180 L/min|
Maximum single fault steady pressure
Device will shut down in the presence of a single fault if the steady state pressure exceeds: 30 cm H2O for more than 6 sec or 40 cm H2O for more than 1 sec.
Pressure level measured according to ISO 17510-1:2007 (CPAP mode):
Power level measured according to ISO 17510-1:2007 (CPAP mode):
Declared dual-number noise emission values in accordance with ISO 4871:1996.
|Physical - device and water tub|
|Dimensions (H x W x D):||4.57" x 10.04" x 5.91"
(116 mm x 255 mm x 150 mm)
|Air outlet (complies with ISO 5356-1:2004):||22 mm|
|Weight (device and standard water tub):||44 oz (1248 g)|
|Weight (device and cleanable water tub):||44 oz (1248 g)|
|Housing construction:||Flame retardant engineering thermoplastic|
|Water capacity:||To maximum fill line 380 mL|
|Standard water tub - material:||Injection molded plastic, stainless steel and silicone seal|
|Cleanable water tub - material:||Injection molded plastic, stainless steel and silicone seal|
|Maximum heater plate:||154°F (68°C)|
|Maximum gas temperature:||≤ 106°F (≤ 41°C)|
|Standard:||Material: Polyester non woven fiber
Average arrestance: >75% for ~7 micron dust
|Hypoallergenic:||Material: Acrylic and polypropylene fibers in a polypropylene carrier
Efficiency: >98% for ~7-8 micron dust; >80% for ~0.5 micron dust
ResMed confirms that device meets the Federal Aviation Administration (FAA) requirements (RTCA/DO-160, section 21, category M) for all phases of air travel.
|Technology used:||3G (USA and Canada only)
2G GSM (all regions except USA and Canada
IC ID: 9103A-AIR103G (USA and Canada only)
The AirCurve 10 device complies with Industry Canada license-exempt RSS standards.
FCC ID: 2ACHL-AIR103G
The AirCurve 10 device complies with FCC Rules.
|Operating pressure range|
|ASV, ASVAuto:||4 to 25 cm H2O|
|CPAP||4 to 20 cm H2O|
|Maximum flow:||15 L/min (CPAP, ASV); 4 L/min (ASVAuto|
|Pneumatic flow path||
|Device, power supply unit:||5 years|
|Cleanable water tub:||2.5 years|
|Standard water tub, air tubing:||6 months|
The patient is an intended operator
- 2 Year Limited Warranty
We want you to be completely satisfied with your purchase. You may return your purchase within 30 days of receipt - see below for exceptions. To qualify for a return, please note the following:
- Product must be unused, clean and not damaged
- Original packaging and materials intact (i.e. instructions, warranty information)
- Return shipping costs are the responsibility of the customer
A 15% restocking fees applies to all returns.
There are no returns on the following categories of products:
- Custom equipment
- Ultralightweight wheelchairs
- Sport wheelchairs
- Lift Chairs with custom fabrics and/or heat and massage
- Bath safety equipment
- Wound care
- Orthopedic supplies
To return a product, the above conditions must be met. We require that all returns follow these instructions for proper processing:
- Call or email to request Return Authorization Number (RA)
- Warehouse must receive item within 15 days of an RA# being issued
- Report via phone or email a tracking number to customer service
- Items sent without an RA number cannot be credited
- The buyer is responsible for return postage costs
All credits will be given after receipt and warehouse inspection approval.
Inspect Your Product When It Arrives
Damaged or Defective Products: Please inspect your package when it arrives. If it is defective, damaged or short an item please notify us within 3 business days of delivery. Customer Service toll-free 888-982-8889. If you receive a damaged product we will replace any damaged or defective parts or replace the product at manufacturer's discretion.
Our service area covers most of Southern California including Los Angeles and surrounding cities.
To see a full list of cities covered in our service area please click here.